• 12336 Emerson Dr, Brighton, MI 48116

Booth Coat 5140

Water based Protective Coatings, Strippable Coatings For Auto Body  Shop Paint Spray Booth

buy-now-blue-300x73

Product Description

General Chemical’s Boothcoat 5140 is a temporary clear peelable coating for paint spray-booth walls, ceilings, floors and other surfaces where paint over spray accumulation must be readily removed. Boothcoat 5140 can be used as a peelable coating on steel surfaces to eliminate flash rusting or as protection on glass, plexi-glass, rubber, cement, aluminum and many other hard surfaces.

Boothcoat 5140 represents the ultimate in non-solvent peelable coatings. It is well stabilized against brittleness and it will not be softened or penetrated by most solvent-based paints. Boothcoat 5140 has no VOC’s.

Features:

  • Results in a reduction of labor costs by reducing the application time.
  • Once cured, it provides an extremely tough, uniform film thickness.
  • Curing time can be cut in half with the use of increasing temperatures up to 130ºF.
  • Easily removed…peels off in sheets which eliminates messy hand scrapping
  • Safe…non flammable when wet
  • Formulated for sag control on vertical surfaces.

How To Apply:
Boothcoat 5140 coating when applied improperly can cause problems. Proper application results in a tough film of uniform thickness with no sags, less application time and minimal clean-up labor. General Chemical’s waterborne clear peelable coating may be used wherever temporary protective coatings are needed to reduce cleanup problems. Spray-booths, floors, windows, walls, machinery, equipment and fixtures have all been applications for peelable coatings. If you have an overspray problem, a cleanup problem or an emissions problem, call us.

1. Apply 10-12 mils wet water based peelable film to clean, dry surfaces (booth walls, fixtures) in a smooth, continuous spray. If using airless equipment, use .015 or .017 nozzle at a set pressure of 1200-1500 PSI. With conventional air spray, we recommend Binks nozzle #68PB with needle #368 at a pressure of 35-55 PSI.
2. After significant paint overspray buildup, film may be quickly and easily removed. Cut film to start peeling from one corner. Production time between cleaning is increased; quality control is improved with better illumination.
3. Simply peel off in large, continuous sheets. Booth is left clean and ready for next application. Messy hand scraping or solvent removal eliminated. Clean-up is fast. Waste disposal costs cut.
4. The coating provides a tough, flexible solvent-resistant film which protects booth walls, paint fixtures, metal parts in storage, or any non-porous metal surface from paint overspray.

Boothcoat 5140 is normally used as received. It is applied by airless spray, roller or brush . The sprayed peelable coating air-dries in 10 minutes to 3 hours, depending on thickness of the coating, humidity, temperature and air movement. Boothcoat 5140 is applied to form a film thickness in the range of 2 to 5 mils (.002″ to .005″). The coating is resistant to attack by most paint solvents. Application temperature is ambient to no lower than 60° F. Boothcoat 5140 coating cures upon water evaporation. Improved air movement and temperatures up to 130ºF will cure this coating in as little as ten minutes.

Removal Characteristics of white peelable booth coating : to be removed by peeling it off.

Flammability
STRIPAWAY_5140 Peelable coating is water borne coatings that presents no fire hazard in wet as received or during application.

Disposal
During removal, water hose-down type coatings will oftentimes be mixed into the paint spray booth water compound system. 5140 peelable coating is normally compatible with this kind of system.

Booth Coat 5140 is uniquely formulated excluding ingredients that are deleterious to the painting process (such as silicones) or the water washes system (such as foam generation or stabilizing ingredients).

Operating Guidelines:
1.When applying 5140, use the same protection as used while applying paint. The booth ventilation system

2.should be operating while the material is being sprayed.
3.Chemical goggles and impervious gloves should be worn when handling or mixing.
4.Use of non-sparking metal is advised to scrape or spud to remove booth coating to avoid fire hazard from accumulated paint.

First Time Application:
If the Our peelable coating film rips or tears, the flap may be lifted and resealed by applying a fresh wet coat to the underside and resealing. Alternatively, cut away flap and re-apply fresh coating, it will bond to itself.

I. Pre-cleaning of Equipment:
To clean pressure pot, airless equipment, spray guns, spray lines, do the following:

1. Flush equipment and lines with current paint thinner (ex. Toluene, MEK, Xylene, etc.)
2.Follow with a water reducible solvent such as Butyl Cellosolve. This will help remove solvent residue.
3.Now thoroughly rinse with water. Make sure all solvent and paint residue is removed
II. Pre-cleaning of Spray Booth Walls:

To clean all surfaces where BOOTH COAT5140 is to be applied, do the following if the last peelable coating that was used was a solvent-based product (this will aid in the first time peel/water removal of BOOTHCOAT5140.
1.Clean surface with butyl-Cellosolve type cleaner.

2.Remove all previous peelable coatings, oils and dirt, and solvent residue from Surface.
The dry Our peelable coatings strippable coating film can be easily removed either by hand stripping or other means. Our peelable coatings are thermoplastic. Do not try to remove in freezing conditions. Our peelable coatings becomes brittle in freezing condition.

NOTE: You do not have to do this cleaning step to have BOOTHCOAT5140 peel/water rinse off of the surface. Although it aids in the first time water rinse/peel of the product. Second and continuous applications can eliminate this step.
3.You are now ready to use BOOTHCOAT5140.